Konfigurasi Routing Dynamic OSPF Menggunakan Cisco Packet Tracer (1 Server, 3 Router, 3 Swicth dan 4 PC Client)

 TOPOLOGI

 (1 Server, 3 Router, 3 Swicth dan 4 Client)

 Berikut adalah pembagian  IP Address pada Router

Setelah itu kita setting IP Address pada setiap Router

Router1

Router>enable
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#hostname SATU
SATU(config)#interface GigabitEthernet0/0
SATU(config-if)#ip address 5.5.5.1 255.0.0.0
SATU(config-if)#no shutdown
%LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state to up
SATU(config-if)#exit
SATU(config)#interface GigabitEthernet0/1
SATU(config-if)#ip address 192.168.12.1 255.0.0.0
SATU(config-if)#no shutdown
%LINK-5-CHANGED: Interface GigabitEthernet0/1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/1, changed state to up

Router2

Router>enable
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#hostname DUA
DUA(config)#interface GigabitEthernet0/0
DUA(config-if)#ip address 5.5.5.2 255.0.0.0
DUA(config-if)#no shutdown
%LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state to up
DUA(config-if)#exit
DUA(config)#interface GigabitEthernet0/1
DUA(config-if)#ip address 6.6.6.1 255.0.0.0
DUA(config-if)#no shutdown
%LINK-5-CHANGED: Interface GigabitEthernet0/1, changed state to up
DUA(config-if)#exit
DUA(config)#interface GigabitEthernet0/2
DUA(config-if)#ip address 10.10.10.1 255.255.255.0
DUA(config-if)#no shutdown
%LINK-5-CHANGED: Interface GigabitEthernet0/2, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/2, changed state to up

Router3

Router>enable
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#hostname TIGA
TIGA(config)#interface GigabitEthernet0/1
TIGA(config-if)#ip address 192.168.23.1 255.255.255.0
TIGA(config-if)#no shutdown
%LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state to up
TIGA(config-if)#exit
TIGA(config)#interface GigabitEthernet0/2
TIGA(config-if)#ip address 10.10.10.2 255.0.0.0
TIGA(config-if)#no shutdown
%LINK-5-CHANGED: Interface GigabitEthernet0/1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/1, changed state to up

Setelah itu asukan IP Address ke Server dan IP Client sesuai dengan tabel di bawah ini

Setelah itu kita konfigurasi routing dynamic OSPF pada setiap Router

Router1

SATU>en
SATU#conf t
Enter configuration commands, one per line. End with CNTL/Z.
SATU(config)#router ospf 1
SATU(config-router)#network 5.5.5.0 0.0.0.255 area 0
SATU(config-router)#network 192.168.12.0 255.255.255.0 area 0

SATU(config-router)#end
%SYS-5-CONFIG_I: Configured from console by console

Router2

DUA>en
DUA#conf t
Enter configuration commands, one per line. End with CNTL/Z.
DUA(config)#router ospf 1
DUA(config-router)#network 5.5.5.0 0.0.0.255 area 0
DUA(config-router)#network 6.6.6.0 0.0.0.255 area 0
DUA(config-router)#network 10.10.10.0 0.0.0.255 area 0
DUA(config-router)#end
%SYS-5-CONFIG_I: Configured from console by console

Router3

TIGA>en
TIGA#conf t
Enter configuration commands, one per line. End with CNTL/Z.
TIGA(config)#router ospf 1

TIGA(config-router)#network 6.6.6.0 0.0.0.255 area 0
TIGA(config-router)#network 192.168.23.0 0.0.0.255 area 0
TIGA(config-router)#end
%SYS-5-CONFIG_I: Configured from console by console

Setelah itu coba ping lagi dari salah satu PC ke Server dan Server ke salah satu PC untuk mengecek apakah semua host sudah terhubung

Ping dari Server-PC

Ping dari PC-Server

Jika hasil ping sudah seperti pada gambar diatas maka semua host sudah terhubung.

"SEKIAN"